Vibro-meter 620-002-000-113 620-003-111-112 VM600 XI016T

Description

Power supply
VM600Mk2/VM600 RPS6U rack power
supplies
: A VM600Mk2/VM600 ABE04x system rack can have either one or
two RPS6U rack power supplies installed, as follows:
• 1 × RPS6U power supply (330 W) supports the power requirements
for a full rack of modules (cards) in applications with operating
temperatures up to 50°C (122°F).
• 2 × RPS6U power supplies (330 W) – operating redundantly –
supports the power requirements for a full rack of modules (cards)
in applications with operating temperatures up to 50°C (122°F).
With this rack power supply redundancy, if one RPS6U fails, the
other will provide 100% of the rack’s power requirements so that the
rack will continue to operate.
Note: This is known as a redundant RPS6U rack power supply
configuration.
• 2 × RPS6U power supplies (330 W) – operating non-redundantly –
supports the power requirements for a full rack of modules (cards)
in applications with operating temperatures above 50°C (122°F),
where RPS6U output power derating is required.
Note: Even though two RPS6U rack power supplies are installed in
the rack, this is not a redundant RPS6U rack power supply
configuration.
Refer to the VM600Mk2/VM600 RPS6U rack power supplies
data sheet and a VM600Mk2/VM600 machinery protection system
(MPS) hardware manual for further information.
Power supply check relay
Nominal switching capacity

(resistive load)
: 4 A / 250 VAC, 3 A / 30 VDC
Maximum switching power
(resistive load)
: 1000 VA, 90 W
Maximum switching voltage : ±30 VRMS / ±42.4 VAC(PEAK) or 60 VDC
Maximum switching current : 4 AAC, 3 ADC
Environmental
According to IEC 60068-2 recommendations
Temperature
• Operating : 0 to 70°C (32 to 158°F)
• Storage : −40 to 85°C (−40 to 185°F)
Humidity : 0 to 90%, non-condensing
Vibration : 10 to 55 Hz, 0.35 mm peak, 6 hours in each direction
Shock : 15 g peak, 11 ms, half-sine pulse
Indoor use : Limited to indoor use only
Designation Ordering number (PNR)
ABE040 Different versions of the VM600Mk2 ABE040 system rack:
– Standard version 204-040-100-016
ABE040 Different versions of the VM600Mk2/VM600 ABE040 system rack:
– Standard version 204-040-100-015
– Varnished version, with a conformal coating for additional
environmental protection 204-040-100-015L
– Separate circuits version, in accordance with the IEC 60255-5 standard 204-040-100-115
– CCSAUS version, in accordance with the IEC 61010-1 standard 204-040-100-214
ABE042 Different versions of the VM600Mk2/VM600 ABE042 system rack:
– Version with mounting brackets positioned at the rear of the rack 204-042-100-01h
– Varnished version, with a conformal coating for additional
environmental protection 204-042-100-01hL
Different blank panel kits for the front of a VM600Mk2 ABE04x system rack:
– 1 × slot wide / 4 HP (TE) 200-505-011-012
– 3 × slots wide / 12 HP (TE) 200-505-018-012
Different blank panel kits for the rear of a VM600Mk2 ABE04x system rack:
– 1 × slot wide / 4 HP (TE) 200-505-011-012
Different blank panel kits for the front of a VM600 ABE04x system rack:
– 1 × slot wide / 4 HP (TE) 200-505-015-011
– 2 × slots wide / 8 HP (TE) 200-505-016-011
– 3 × slots wide / 12 HP (TE) 200-505-018-011
– 4 × slots wide / 16 HP (TE) 200-505-017-011
Different blank panel kits for the rear of a VM600 ABE04x system rack:
– 1 × slot wide / 4 HP (TE) 200-505-011-011
– 2 × slots wide / 8 HP (TE) 200-505-012-011
– 4 × slots wide / 16 HP (TE) 200-505-013-011