Name: GE D20 MIC 10BASE-T - Runheng
Brand: GE

GE D20 MIC 10BASE-T

GE D20 MIC 10BASE-T
Individual products of the D20 and D200 automation product family are classifiedaccording to EU Directive 2004/108/EC as subassemblies / finished appliancesexclusively intended for an industrial assembly operation for incorporation into otherapparatus. They are not apparatus in the sense of the EMC Directive.To achieve CE mark compliance, the end user shall be responsible for ensuring thefinal system/installation conforms to all requirements of the European UnionElectromagnetic Compatibility (EMC) and Low Voltage (LV) Directives. Productsinstalled in secondary EMC grade protection metallic cabinets and following properinstallation practices depicted in D20/D200 User Manual should meet CE markrequirements.For information regarding current regulatory compliance status of your order, pleasecontact your local sales representative or email us at energy.salescalgary@ge.com.Classification ofThe D20 and D200 line of products are intelligent, industrial grade control devicesD20/D200targeted for automation and control of electrical substations. These products areProducts fromdesigned as modular and scalable devices allowing the non-consumer end user tothe EMCbuild a system of virtually any size and complexity. The number of options andDirectiveconfigurations can be large; therefore, trained personnel must be involved in thePerspectivedesign and integration of the final system. Refer to the explanatory note below.Due to the inherent complexity and almost limitless variations of final systems, it isnot possible for the manufacturer to guarantee compliance in the factory ofindividual D20/D200 modules in a final system, with the exception of pre-assembledRTU cabinets. Therefore, the end user shall be responsible for ensuring the finalsystem/installation complies with all requirements of the EMC and LV Directives.RadiatedThe D20 and D200 products have been designed and hardened to operate in theEmissions andharsh industrial environment of electrical substations. When placed in service, theRadiatedfinal system must conform to the objectives of the EMC Directive. To meet RFemissions and RF susceptibility according to CISPR 11 Class “A”, all D20 and D200ImmunityConsiderationsproducts must be installed in an EMC grade secondary metallic protectiveenclosure/cabinet. Additional EMC countermeasures may have to be applieddepending on complexity and size of the system.

Add to Quote

Category: GE

Email: Jiedong@sxrszdh.com
Phone: +86 15340683922
Sales:Wu Jiedong

All prices listed on the official website are subject to confirmation by contact: Wu Jiedong (manager).
Our product: brand new original packaging
Our payment: 100% telegraphic transfer of inventory items before shipment, conditions can be proposed!
If you have any downtime spare parts that you cannot find, please feel free to call or use email to contact me. If there are issues that the product cannot solve, please contact me. Product prices can be negotiated. Please do not consider contacting me!

Description

GE D20 MIC 10BASE-T
Follow these practices at all times:Don’ts1. Surge and noise suppression components used on the D20 and D200 aredesigned to conduct during transients to prevent nuisance operation or damage tointernal components. To ensure shunting of transients from line to ground, theD20’s and D200’s earth ground stud must be connected to a low impedanceground using braided cable or heavy solid copper conductor (12 AWGrecommended). When making ground connections, ensure that all surfaces thatare used for grounding are free of dirt, residue and corrosion. A coating such asglyptol can be used to protect these connections from oxidation and dirt deposits.2. Ensure that cable shields are grounded at either the D20 or D200 auxiliaryground stud or at the field equipment. Do not ground the shields at more thanone point because a potential difference may exist between grounds causingground loops and undesirable noise sources.3. Ensure that all nuts and screws are properly tightened.4. Always replace fuses with the same type and rating used by GE Energy. For fusetypes and ratings, see “Servicing”, page 118.5. When connecting to communications equipment such as modems or radios,always use appropriate surge protectors to protect the communication ports.6. To prevent interference with communications, route all communication cablesaway from power-carrying cables.7. Always fuse-protect field sources.8. Always configure the jumpers in your D20 or D200 prior to connecting field I/O.9. Follow all instructions in this guide as they are presented.10. Do not operate the D20 or D200 if it has been dropped or damaged. Return it toGE Energy for inspections and repair.11. The D20 and D200 power supplies use switching technology. For properoperation, the input voltage must be within specified limits prior to turning onthe D20’s or D200’s power switch.12. Do not apply voltages outside the range of the product specifications. Voltagesoutside the specified range may lead to premature product failure.13. Do not modify the D20 or D200 without prior written authorization form GEEnergy.Make sure the D20 or D200 is grounded using the protective ground stud.Connection must be provided with separate green/yellow wire connected between!the D20 or D200 and the protective earth system of the facility. Minimum 12 AWGis recommended

GDB021BE01-GDB021BE-HIEE300766R0001-ABB card

GVC736CE101-3BHE039203R0101-5SXE12-0184-ABB-card

HC-KFS23K-S49-motor

IMHSS03-ABB-card

KUC321AE-HIEE300698R0001-ABB-controller

PCD235A101-3BHE032025R0101-ABB-controller

PFEA111-20-ABB-Relay

PFEA112-20-3BSE030369R0020-ABB – relay

PFEA112-65-3BSE050091R65-ABB-relay

PFSK151-3BSE018876R1-ABB-card

PFSK152-3BSE018877R1-ABB-card

PHARPS32200000-F8-G2B9B3B6-ABB – new original

PM511V08-ABB-control unit

PM511V16-3BSE011181R1-ABB-DCS control unit

PM803F-3BDH000530R1-ABB-controller

PM864AK01-eA-3BSE018161R2-ABB-Module

Email: Jiedong@sxrszdh.com
Phone: +86 15340683922
Sales:Wu Jiedong

Our products are guaranteed for 1 year, with new and original production stopped and imported spare parts.
All prices listed on the official website are subject to confirmation by contact: Wu Jiedong (manager).
Our product: brand new original packaging
Our warranty: All new or repaired parts have a 12 month warranty period beginning
Our payment: 100% telegraphic transfer of inventory items before shipment, conditions can be proposed!
If you have any downtime spare parts that you cannot find, please feel free to call or use email to contact me. If there are issues that the product cannot solve, please contact me. Product prices can be negotiated. Please do not consider contacting me!