GE IC200ALG327H

Description

Product Description
Analog Input Module IC200ALG230 / BXIOAI4 provides an interface to
either 4 voltage inputs or 4 current inputs.
Analog Input Module IC200ALG260 / BXIOAI8 provides an interface to
either 8 voltage inputs or 8 current inputs.
ANALOG INPUT 12BIT
VOLT/CURR CH
The module receives power from the backplane power supply. No
external power source is required for module operation. Power for the
user’s transceivers must be supplied from an external source.
Diagnostics
The module reports a Loss of Internal Power fault for field-side circuits.
LED Indicators
The green INT PWR LED indicates the presence of internally-generated
field power for the analog field-side circuits.
The green OK LED is on when backplane power is present to the
module.
Configuration Parameters
Two jumpers on the carrier terminals can be used to configure voltage or
current mode and unipolar or bipolar operation in voltage mode. One
jumper selects either voltage or current operating mode. With this jumper
connected, the module accepts current inputs in the 4mA to 20mA range.
With no jumper installed the module accepts -10VDC to +10VDC inputs.
In voltage mode, another jumper on the carrier can be used to select the
0 to 10VDC range.
Preinstallation Check
Carefully inspect all shipping containers for damage. If any equipment is
damaged, notify the delivery service immediately. Save the damaged
shipping container for inspection by the delivery service. After unpacking
the equipment, record all serial numbers. Save the shipping containers
and packing material in case it is necessary to transport or ship any part
of the system.
Module Characteristics
Channels IC200ALG230 / BXIOAI4: 4 single ended, one
group
IC200ALG260 / BXIOAI8: 8 single-ended, one
group
Module ID IC200ALG230 / BXIOAI4: FFFF9004
IC200ALG260 / BXIOAI8: FFFF9008
Isolation:
User input to logic
(optical) and to frame
ground:
Group to group:
Channel to channel:
250VAC continuous; 1500VAC for 1 minute
Not applicable
None
LED indicators INT PWR LED indicates internally-generated field
power is present. OK LED indicates backplane
power is present
Backplane current
consumption
IC200ALG230 / BXIOAI4: 5V output: 125mA max.
IC200ALG260 / BXIOAI8: 5V output: 130mA max.
External power supply None
Thermal derating None
Configuration parameters Range select, Mode select (jumpers on carrier)
Diagnostics Loss of Internal Power
Input Characteristics: Voltage Mode (Default)
Input voltage: Bipolar: +/-10VDC (default)
Unipolar: 0 to 10V (configurable)
Input Impedance 126kOhms maximum
Accuracy at: 25 degrees C*
0 to 60 degrees
C
+/-0.3% typical of full scale,
+/-0.5% maximum of full scale
+/-1% maximum of full scale
Resolution: Bipolar mode:
Unipolar
mode:
2.5mV = 8 counts
2.5mV = 8 counts
Filter response 5.0ms
Update rate per module 0.4ms
Common mode voltage 0 V
Channel-to-channel
crosstalk rejection
30dB minimum
Input Characteristics: Current Mode
Input current 4 to 20mA
Input Impedance 200 Ohms maximum
Accuracy at: 25 degrees C*
0 to 60 degrees C
+/-0.3% typical of full scale,
+/-0.5% maximum of full scale
+/-1% maximum of full scale
Resolution 4A = 8 counts
Filter response 5ms
Update rate per module 0.4ms
Channel-to-channel
crosstalk rejection
30dB minimum
* In the presence of severe RF interference, (IEC 1000-4-3, 10V/m), accuracy may be
degraded to +/-3%.

3504E Triconex Features

SVM1608/SER.102 CMZ manufacturing and characteristics

SR469-P5-HI-A20-E installation features

PR9268/201-000 EPRO sensor

PR9268/201-000 EPRO sensor

Relevant process of PPC322BE ABB controller

5PP320.1505-39 Working principle and application of B&R

FLUKE190-202 FLUKE maintenance

3201 TRICONEX handling method

IC754CGL12CTD-FH GE equipment common sense